Oct 15 01:06:11 fedora64 kernel: Attached scsi removable disk sdd at scsi7, channel 0, id 6, lun 0Since I formatted most of my zip disk like they were floppies, there is no partition table so something like /dev/sdd1 wouldn't work. Oct 15 01:06:11 fedora64 kernel: sdd: unknown partition table Oct 15 01:06:11 fedora64 kernel: sdd: assuming drive cache: write through Oct 15 01:06:11 fedora64 kernel: sdd: cache data unavailable Oct 15 01:06:11 fedora64 kernel: sdd: Write Protect is off Oct 15 01:06:11 fedora64 kernel: Type: Direct-Access ANSI SCSI revision: 02 Oct 15 01:06:11 fedora64 kernel: Vendor: IOMEGA Model: ZIP 100 Rev: C.18 Oct 15 01:06:11 fedora64 kernel: scsi7 : Iomega VPI0 (ppa) interface Oct 15 01:06:11 fedora64 kernel: ppa: Communication established with ID 6 using EPP 32 bit Oct 15 01:06:11 fedora64 kernel: ppa: Found device at ID 6, Attempting to use EPP 32 bit The 2.0.36 gives you a clue how long its been since I've used my zip drives! 8-)Ĭode: Oct 15 01:06:11 fedora64 kernel: ppa: Version 2.07 (for Linux 2.4.x) sbin/modprobe /lib/modules/2.0.36/scsi/ppa.o 0x278,0Įcho "To format: mkfs -t ext2 /dev/sda4 98288"Įcho "To mount: mount -t ext2 /dev/sda4 /mnt/zipdrv I put a bash script in my home account (I was the only one to use the zip) which had the folowing lines: The value 98288 was reported by the fsck program. After modprobe is run then either the mount command is executed to mount the disk in the drive, or that disk is replaced with an unformatted disk and the following command is run: Then you had to be sure a disk was in the drive before doing a modprobe, which will allow modprobe to get the correct size from the hardware. Mine was a parallel one and I had to add the following line to nf:Īppend="ppa=0X278,0" prior to any device stanza, and then run /bin/sbin/lilo as root to update the boot loader. Being a new emachine I'm assuming your parallel port is a bi-directional one isn't it? Is your Zip-100 for a parallel port or is it an ATAPI version? Sorry you didn't get your Zip-100 to work, Mister-Ed. Thanks in advance for any help you can share with me. Please post your replies to this forum so that others may benefit too. There is media in the drive.Īny ideas of where to look or what to do? Immediately I get the message "mount: No Media Found". * Tried to mount the zip drive: " mount /mnt/zip " * Added the following line to /etc/fstab: " /dev/sda4 /mnt/zip vfat noauto,rw,user,nosuid,sync 0 0 " * Created my mount point: " mkdir /mnt/zip " * Added the following line to /etc/rc.d/rc.local: " /sbin/modprobe ppa " All of the following was done as the root user. The rest came from old RedHat postings and from The Linux Doc Project. Most of the instructions I followed came from this forum. * I did not attempt any system configuration except what was done during installation process. * Installed a fresh Fedora Core 2 from CD's, no updates to an existing installation. The mount command complains "No Media Found" although I know it is there and the drive is properly connected to the system. I'm having a problem getting a parallel port Zip 100 drive to mount. To actually read the data you copy over, you'll need to figure out how to use virtual machines or emulators such as DOSBox and vintage applications to convert your data into a format you can use, and that's far beyond the scope of what we're going to cover below.Being a newcomer to Fedora Core, I currently seek good sources of technical information and assistance. Related: How To Use DOSBox To Run DOS Games and Old Apps Once the data is safely on your new machine, it might be trapped in an obsolete file format that your modern apps can't read or understand. The Big Caveat: Copying Is the Easy Partīefore you get too excited about transferring data from a vintage Zip disk to a modern computer, you need to know that successfully copying data is only half of the solution. Is your priceless data locked away on an Iomega Zip disk from the 1990s or 2000s? There are several easy ways you can copy files from Zip disks over to a modern PC or Mac yourself. When All Else Fails, Contact a Data Recovery Service.How to Copy Data from a Zip Disk to Windows.How to Copy Data From a Zip Disk to a Mac.First, Assess the Condition of Your Zip Disks.The Big Caveat: Copying Is the Easy Part.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |